Vulnerability of the point-and-point glass curtain wall design

The product of the modernization process, the point-supported glass curtain wall, also has certain defects in its design. We must reasonably understand it and choose the right product according to our own needs. What are the design vulnerabilities? Let’s take a look!

1. The main accessories of the point-supporting curtain wall, the connecting claws and the connecting bolts are mainly made of stainless steel. However, the selection of stainless steel at this stage is quite confusing. Many engineering designs do not have clear stainless steel models and use inappropriate stainless steel. This caused a lot of engineering to appear rusty in stainless steel. There are more than 200 varieties of stainless steel, not all of which can be used as point-supporting curtain wall fittings. The point-supporting curtain wall fittings are bare outside, and the requirements for corrosion resistance are relatively high.

We believe that when stainless steel is used, the most suitable type should use stainless steel containing 18% chromium and 8% nickel. When all metals are oxidized with air, an oxide film is formed on the surface. The oxide formed on ordinary steel will continue to oxidize to form a rusted surface. However, since the stainless steel contains at least 11% of chromium, the properties of the oxide layer are changed to prevent further oxidation, and if the oxide film is accidentally removed, a new oxide film is formed and continues to protect.

2. The design of the connection between the metal plate and the glass of the glass rib support point-supported curtain wall is unreasonable.

The glass-ribbed point-supported curtain wall overcomes some of the shortcomings of the traditional all-glass curtain wall and has been used more and more in recent years. Traditional all-glass façades, when the height exceeds 6m, tempered glass is no longer available. Because the current domestic tempering furnace can temper 6m long glass and all glass curtain wall with height more than 6m, only non-tempered glass can be used. When the non-tempered glass is broken, it will hurt people and the strength is relatively low. The strength of tempered glass is 3 to 5 times that of non-tempered glass. Therefore, thicker glass is required to meet the strength. The extra long thick glass is more expensive and the installation is more complicated. Then, the point-supported curtain wall supported by the glass rib overcomes the above disadvantages. |Exam big|ribbed support glass is to divide the glass into smaller pieces. With thinner tempered glass, it can meet the strength, the price is cheap, the strength is high, and it will not hurt when broken. Glass ribs are generally joined by stainless steel plates. In practical applications, designers generally choose multiple bolts to fix glass ribs and stainless steel plates. Glass is a brittle material that is porous and does not increase the load carrying capacity of the glass. Because we found in the test that we could not do it, the force of each hole was the same, so one glass hole was broken and the whole glass was broken. Therefore, the number of holes does not increase the load carrying capacity of the glass. Generally, one end of the glass rib with a small cross-section height can be fixed by two bolts. The end of the glass rib with a large cross-section height can be fixed with up to 3 bolts.

3, lamination, hollow glass opening should pay attention to the difference

Laminated and hollow glass are used more and more in point-supported glass curtain walls. In the actual project, the opening of the glass is prone to some problems, and the docking bolt is not installed in the glass hole. The main problem is that the laminated rubber and the insulating glass are all made of two or more layers of glass. Many of the inner and outer layers of the glass have the same aperture. The processing process is first drilling, tempering, and then laminating or insulating glass. After the glass is drilled, there will be some allowable deviation in the hole pitch. If the direction of the deviation is opposite, after the synthetic lamination and insulating glass, the diameter of the hole will not meet the design requirements, and the glass hole stack will appear. Therefore, in order to avoid the above situation, the diameter of the inner glass hole is larger than that of the outer glass to digest the difference of the glass holes.

These design defects of point-supported glass curtain wall, many designers, experts are also further research, hoping to design more and more perfect products, make our life more convenient and faster!

For over 100 years, AKH Die Casting has been dedicated to providing companies with superior die casting and tooling, along with metal finishinig and CNC MACHINING AND Grab Bar  through state of the art machinery and processes. Specializing in ALUIMNUM and ZINC ALLOYS, engineers and production staff will develop a high pressure die casting process that will produce your parts economically and with reliable quality

Advanced Die Casting Technology

NINGBO AIKEHAN continues to invest in state of the art machines and technology to provide process consistency, precision, and reduced labor. Combining automated process monitoring and an expert staff of process technicians means we can quickly detect process issues and correct for out of control variables.

Utilizing a licensed vacuum system, we improve the surface finish and integrity of our castings and molds, ensuring our clients receive only the highest quality work from the Premier team.


.

Aluminum Die Casting Parts

Aluminum Die Casting Parts,Aluminum Led Housing,Aluminum Heatsink Profile,Extruded Aluminum Heatsink

NINGBO AIKEHAN METAL PRODUCT CO.,LTD , http://www.diecastingsupplier.com